Jump to content
Search In
  • More options...
Find results that contain...
Find results in...
superhawk18

x400 fish (70kHz) and P66 (50kHz/200kHz) interference?

Recommended Posts

Good Day, I am currently running a P66 for my FF. As the P66 is dual mode 50/200 - and the x400 is at 70, will I have any issue if I mount the two transducers on the same transducer mounting plate on the starboard side? Currently P66 is mounted directly to transom, planning on pulling it off, installing the plate, then installing both the P66 and x400 transducers as far apart on the plate as possible (12 inch plate). X400 specs say anything within 20kMz of their 70kMz may be an issue. I would still like to utilize the 50kMz option on my FF. 

 

Anyone have this setup? Something close?

 

Thanks, Dave 

Share this post


Link to post
Share on other sites

 

I am assuming that when you refer to a x400 you really mean a Fish Hawk X4 or X4D ?

 

I run an Airmar B60 50/200, which is the thru hull version of the P66, and  a X4 together on my boat and have never seen any interference between them.  I'm usually running both 50 and 200 kHz on a split screen.

I also have a Lowrance 83/200kHz transducer that is mounted only 5" away from the Fish Hawk and I will occasionally run it at 83kHz with no problems. I will see cross talk interference on my HDS units if I run both transducers at 200khz together but still not have any problems with the Fish Hawk.

 

I do have the Fish Hawk transducer mounted higher on the transom than the 83/200 so that it is a little above the bottom of the boat and it is not causing turbulence when I'm on plane

Share this post


Link to post
Share on other sites

Yes, sorry, X4. Sounds like I will be OK, thanks for the details. I will have these about 6 or 7 inches apart. 

Share this post


Link to post
Share on other sites

My fishhawk and garmin unit cross talk at the lower frequencies. The signal comes and goes. Some days it dosen't bother as much as others which I don't understand.

 

Share this post


Link to post
Share on other sites

I sent fishhawk a picture of my transom and they made a suggestion but said it may help. Did't seem worth all the work for may help. Not their fault, the frequencies are just to close. 

Share this post


Link to post
Share on other sites

dry net, do you know the frequency of your garmin transducer?

 

 

Sent from my iPhone using Lake Ontario United

 

Share this post


Link to post
Share on other sites
Posted (edited)

One of the factors that may affect things is when someone has a CHIRP depth finder because the frequency range coverage of it could include the 70 khz frequency and this could occur regardless of the transducer placement; especially on smaller boat hulls (than say an ocean liner:lol:).

Edited by Sk8man

Share this post


Link to post
Share on other sites

My garmin unit is a 77/200 hz . Like I said it doesn't bother all the time but on occasion it dose. I have a single transducer mounting plate on the boat. Space is limited because of the kicker. When it dose bother I switch freq for awhile and then turn it back to the lower freq. Most days it only happens once or twice. no my garmin is not a chirp unit. The people at fishhawk were very nice and responsive to my questions. Good luck,    Matt 

Share this post


Link to post
Share on other sites

You can shutdown the sonar mode on one of your units and use the plotter mode with a full screen view. This way you have the best use of your units. Sonar "off" is available,  

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

×