Brian

Ok. Now I'm confused again. Maybe they are a version of mag 10s. All I'm trying to figure out is the cycle function. Can anyone tell me how it sets?thanks

They are definitely digitroll 2s. Now I need to find a manual. Thanks for your help

Thanks. The side cover says magnum 10a on it as well as the neck where the boom mounts. They work fine I just can't find a manual online anywhere.

I was cleaning out my storage building and found these from 20 years ago, and I know they are 10A riggers but I can,t find any info because of the control board mounted on them. All the info on mag 10a show this rigger without control panel. Can someone shed some light on this. I'm looking for a manual on them.

Surface temp was 65 tonight. Nothing shallow for me yet

Yes, Lakers. All but one were decent size.

Set up this morning about 1/2 mile south of Severne.after 40 minutes of trial and error started hiiting fish. Best program was mountain dew SD with big weenie proct. Fly. If it wasn,t green it didn't get touched. All in 130 fow at 1.9-2.1 mph. Surface temp 33-34 down temp 36. Seven fish and only 1 lamprey. Only one other truck at the launch. All in all nice morning on calm water. Good luck .

PM sent

You're sick of hammering those walleyes already??

 

Good luck.

Got out Saturday and it was nice being on the water. Beautiful condtions and plenty of lakers. No LLs. Headed just south of Severne and picked away at fish parked on the bottom in 130 ft. Usual programs...green SDs and flies.

Thanks..Saturday looks good ....north at 3kn.

Anyone know how the launch is at Severne?

When we are painting aluminum, if has been previously painted we wet sand with 400 grit and use automotive base/clear system. If it is bare aluminum, the aluminum is scuffed then sprayed with a self etching primer, then base/clear.

It's an autohelm st50...no longer made...if any one has a cover for the radome I will buy it.

OK...it gets worse . Can a crack be fixed with fiberglass, then painted without issue?

Does anyone know if the radome housing can be painted without affecting the radar ?

Mine is getting a bit weathered .

I ended up finding a 2010 triple axle , 10,000lb trailer for 2500. in jersey. There aren't many around but the people I dealt with were pretty accomodating....Dolphin Trailers in Eastampton NJ...(609) 614-7270. Also check The Star Ledger classifieds and Jersey Shore Craigslist. There were a few but not what I was looking for.

Definately! What bayliner are you fitting?

[ Post made via Android ]

trophy 2860 hardtop

There were a lot of boats destroyed on the jersey shore from hurricane sandy. I am going to look there. At least someone can get some of their money back and maybe I can get a trailer. I'll let you know what I find.

Looking for a used trailer to hold a bayliner 2860

I would like to get a 27' boat from Mexico to syracuse this spring for a new paint job. Does anyone know who does short hauling or trailer rental? Would like to sublet to someone who can move it from the trailer to blocks without damage.

Fished out from Severne launch. Plenty of lakers off spinners and flies parked on the bottom at 110 fow. Not a single hit off the boards or dipsies. Maybe lls are farther south? Any suggestions?

Severne is good to go boats are at the ramp every day pearch fishing. We fished South of Severne today and did close to 40 all Browns Lakers, Salmon and Bows.

That,s the answer I was looking for. Thanks.

Thinking of trying the severne area this weekend. Any reports from the area and is the launch good to go? Thanks.

Can anyone tell me what this spoon was called and maybe about when it would have been made. It is brass and the eyes are glass and appear to be red if cleaned up. Thanks

Left Severne at daybreak trolling south. Picked up 1 LL off the boards with leadcore out 5 colors. Caught and released 7 lakers off the riggers, mostly good fish all in 130fow near bottom. Green spindoctor green fly. Water is high... docks at Severne were completely underwater.