Down Deep
-
Posts
105 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Posts posted by Down Deep
-
-
To add an autopilot to your main motor it must have hydraulic steering , which I did not have ( Next Project ) . I don't know if an autopilot on main motor would work if motor was not running ? Kicker runs great in rough i water Except going straight into rollers , avoid it even with Main motor,
-
PM Sent , will take the 9 stickbaits
-
Look into a Garmin TR-1 Autopilot made for a trolling motor ,Saves wear and tear on your main steering and the driver too . Best purchase I have made .
-
Painted surfaces and stainless ok , just rinse off good also take caution on black plastic will discolor them white , Bare metals watch out . It will eat the galvanizing off a trailer real quick .
-
Never tried muriatic acid , but MaryKate ON & OFF is probably the same stuff and is Great . pressure wash first to get the heavy stuff first . I just wet down trailer and concrete first just in case . I apply on a small folded towel and just wipe on small section at a time so there is no dripping , also do the mercury motor lower unit and trim tabs . Looks like new again . But the stuff is nasty - wear personal protection and careful not to get a whiff of it .
-
Yes , I will ship , give me a call
-
-
-
Up for sale I have a Fish Hawk 840 Complete with Everything needed and an Extra Probe. This unit belonged to a friend who sold his boat to a non-fisherman. Everything is in working order. Tested probes and display unit on my X4. $225. Shipped to your door . If interested, call John at (716) 374- two one 33.
-
No need to remove hatches , check my picture . the gasket goes on the highest part of the well crown , not down in the drain channels . I will take more pics if you want . Gasket makes contact with the underside of cover , not cover lip . Maybe they changed the style in 07 ?
-
That is one thing I never thought of , it would come in handy to charge third battery . will it keep up with amp draw or is it mostly for recharging when docked ?
-
Yes , mine is 5/8" wide and about 1/4" hi , probably flattened out a bit . if it is hollow then it is the same. yours should be fine . When rounding corner go slow and press hard. Apply silicone spray to gasket occasionally .
Just remembered , I had to cut back side of lip a bit on one cover because it would not clear the gasket .
-
Just one on each side is all that is needed .
-
Sold - Pending Payment
-
-
Top and side attach with two # 10 ss screws , length depends on cover thickness . pre drill and start screws first . Then silicone screws and bracket before assembly , will never vibrate loose this way .
-
They are called Spring Hatch Arms (West Marine 4914792 ). The self-adhesive Weather seal I got from Trophy , they started using it in 2009 I think. or you can get close substitute at West Marine 1955046 . Just make sure you degrease area and scuff with Scotch Brite pad or fine sandpaper before applying .
-
I have a 2007 Trophy 2002WA . what Upgrades were you thinking on the Fish wells ? I added rubber gaskets around the rim to keep rainwater out , new latches that are easier to grab and Spring Type hatch holders , you goota have these , keeps the well hatch open - tap the side with your foot or hand and it closes . I probably have every gadget on my Boat Except a Hardtop ( would not fit in the garage ).
-
Tomorrow March 28 is the 4th annual Fisherman's Flea Market. Stop in and find Tons of Fishing Equipment and More . Open 9 am - 3PM
Alexander Firemen's Rec Hall
10708 Route 98
Alexander , NY 14005
-
Contact Phone # To reserve a Table ? Thanks
-
Thanks for the reply Guys .
-
Can someone post full address and contact phone # for Brewerton and Watkins Glen . Thanks
-
-
luhr Jensen super glow / trash can dodger
in Classifieds - Buy, Sell, Trade or Rent
Posted
Trash can finish ? can you post a picture .