Jump to content

jcar585

Members
  • Posts

    28
  • Joined

  • Last visited

Posts posted by jcar585

  1. post-146412-0-47494500-1371052859_thumb.jpgpost-146412-0-95251000-1371047414_thumb.jpgpost-146412-0-22636200-1371047615_thumb.jpgpost-146412-0-70609300-1371047651_thumb.jpg78 glastron hp154 bass boat 15.5 ft

    -84 johnson 75 hp outboard- bought the motor from pugleys this spring, complete rebuild with a 1 year warranty. runs great.

    -2 year old minnkota bow mount trolling motor 40 lb

    -new floor,carpet, wiring, trailer lights

    -rebuilt the transom 2 years ago . my finished top of the transom doesn,t look great but its solid.

    -the bench seat in the boat is a mess and was my next and last project.

    -been out 8 times this year with no problems at all.

    -selling because i have to chance to buy a bigger boat

    1-585-303-9915 call or text. thanks     post-146412-0-73427800-1371045651_thumb.jpg

     $2500 or bo

    will try to get better pics later

  2. Thanks guys! Stinger hook sounds like a great idea! Using my bass set up, baitcaster with a stiff 7' rod. You know one thing i noticed out of Penn Yan was that i got a ton of marks at 50 fow. I didn't really fish that depth because everything i've read indicates the lakers are going to be deeper. But after thinking about it maybe i missed out.  

  3.  Tried jigging Keuka for lakers on the last 2 saturdays with little success. Launched at the state park 2 saturdays ago and one of the guys in the boat caught 3. This was his 1st time jigging as well. All of his fish were caught when i was moving the boat slowly trying to find fish on the ff. We had maybe 5 hits when we were vertical but couldn't hook up. This past saturday launched out of Penn Yan and ran down the lake until i could find fish in 70-100 fow. Got 4 or 5 hits vertical but still no hook ups. Not sure what I'm doing wrong. I've used 1/2 ounce to 1 ounce white jig heads with white flukes or Tubes, 10 pound braided line with a 6 ft 10 lb mono leader. Fish seem to be gone by the time i try to set the hook. There is a lot of guys on here who are good at this so i'm hoping to get some advice. Thanks! 

  4. Thanks for the reply Gez. That's what i've heard also. It's hard to find a reliable used outboard, that's why i was hoping the 40hp would be enough. What would be the biggest problem if i went that low? The boat is so small i'm surprised about the 100 hp max to begin with.

    mail.jpg

  5. Hi everyone, any advice would be appreciated. Plan on buying a used outboard for my hp154 and trying to figure out the minimum horsepower i can get away with. Boat is 700lbs, plate has max hp at 100. I was looking at a 95 40hp but was told by the salesman that it would be underpowered. I dont care about fast speeds but I don't want to cause damage to a motor either. Any input would be great .. Thanks!

  6. Spent a week at honeoye bass fishing with fam. Caught well over a 100 bass with a few walleye but my son caught the one that stood out. 21.5 inches 15.5 girth. We took the pic and let it go.

    Bradon_s_catch_7_8_12.jpg

  7. Hi any help would be appreciated. Bought the outboard this spring. Got it to run on ears but no luck in the water. compression is 110 125 125 110. Spark is good. Rebuilt the carbs, fuel pumps and changed the top and bottom gasket on the bottom cowl because it seemed like exhaust was getting inside the housing and getting sucked into the carbs. Motor seemed to run better after the carb and fuel pump rebuild but no difference in the water. Ive adjusted the air/fuel mix screws on carbs and gotten a smooth idle on land. Ive set the idle higher on land to try to make up for the extra load in water. I noticed the last time out i had water and exhaust coming up through the shift shaft housing just under the front of the cowling. I also changed the impeller and have good flow out of the motor. I plan on dropping the lower unit again to try to figure out where all the water and exhaust are coming from . Exhaust has me completely confused since it has no pipe on the the inside of the crank shaft housing.

    Again any help would be great. Thanks in advance.

  8. Anybody have advice on the best way to repair a bad transom. I restored a 78 glastron bass boat, took it on vacation to conesus last week and by the 2nd day i noticed that the fiberglass on top of the transom had cracked on each side of the motor. The motor is a 79 90 hp, about 300 lbs. I was stuck with my trolling motor the rest of the week Any help would be appreciated. Thanks.

  9. Fished from 6:30 to 8:00 in Palmyra last night. Caught 2 Smb, 7 LMB all between 13 and 17 inches. Last 15 minutes switched from a black 4" senko to a silver minnow and caught a 27" pike. Best thing was i never moved. The 1st Bass i had on was huge but of course i lost that one. Got a good look at it and it was at least 4 pounds. Going back to the spot tonight and bringing a camera. And of course i released them all.

×
×
  • Create New...