retsey

I will also be up over the weekend to listen for the libes to zing..:)

Can someone tell me how to eliminate auto notification when someone starts a new thread? I have tried everything and looked in all areas of my settings. Thank you in advance.

Hello, Does anyone use Raymarine ACU200?

Hello guys, Just seeing if someone can assist on how I am able to go to a waypoint using the autopilot EV200 & Lowrance HDS8 Gen 2. The patterns all appear to be working but not sure how to go on track to a point. I'm wired using NMEA2000 and am connected to the Lowrance with proper cable. I take my cursor to the waypoint to the marina and set to auto but does not take me there. Is there some settings in my Lowrance that needs to be activated? I have tries using the track mode on my Raymarine with no success. The compass on each are within a few degrees. Thank you in advance. Marty

I will be pushing (looking to purchase)a 21'er with a Yamaha 150 & 9.9 high thrust through a Seastar HC5358 hyd steering. BTW, Currently have the S1000 and does not cut it ! Question, What exactly and do I need to spend the $270+/- on a Smart Stick sold through Teleflex? II understand it's a way to measure linear movement and lets the autopilot know where the motor is on the transom. But what I don't understand is if Raymarine suggest (as the RM rep does) that a Smart Stick to be used with there system, why don't they state that in there manual or even sell such a device with there system. Or another way of saying it, if they are selling and autopilot that communicates with the EV1-Sensor that works off the compass,and is a working system, then why the Smart Stick. Is it just added insurance that the autopilot will work much better at those lower speeds? BTW...It seams like Teleflexx sells the Smart Stick but they don't even know what it is for or why its used, I called Teleflex (Seastar Solutions) , Vancouver direct and spoke to Mike Gray. He could not explain it to me. Looking forward hearing from you Retsey

I agree Guys.....Being an engineer myself and engineering heavy equipment with lots of large bearings, this whole Bearing Buddy concept is simply poor engineering and a marketing thing ! ....just wanted to here what opinion others had. I'm sending the BB back for refund Thanks for the comments Retsey

Yes Dan, That's what I was thinking also. Why would one want to push contaminants back into any through the bearings and seals. It's always best to purge the bearing and seals as is done on heavy equipment.

I lost one of my caps so I decided to purchase two sets of Bearing Buddies and replace all of the Cap & Fitting that has a rubber grommet on the end to access the fitting. The end of my axles have a Zerk fitting that obviously forces grease directly down the axle and purges old grease and water out of the bearing. To me, this is the most positive way to get grease direct to the bearing. (just like heavy industry machines). My question is...should I be removing this grease fitting from the end of the axle if I use Bearing Buddies to allow grease to be forced through the axle and to the bearing? Or........maybe just stay with what I have and return the Bearing Buddies??? PS..It would take the same amount of time to remove the bra cap that is covering the Bearing Buddies as it would to reome the grommet , grease and reinstall the the grommet in place. Your comments please. Thank you guys

I was fighting in making the 840 display and the X4 probe talk for +2 years. (I only use the system maybe 2-3 times a year since I don't use it for anything else but Salmon fishing) Also, sent the display back to have it checked, ect... I finally decided to just bite the bullet and buy the new display. All problems went away and I can read bottom temps and speeds with no blinking. I believe you might have to do the same. One adjustment I did make is I lowered the transducer and installed it horizontally. The design of the probe is such that it allows for 15 degree blowback of the ball and has a very wide cone angle.

Before I install the electric reels to my manually operated mast, just wondering if there is a need to install a circuit breaker in the system even the there is a 10 amp switch built into the pushbutton switch? Have you ever tripped the 10 amp breaker during heavy retrieves...and can I depend on the built in breaker to actually protect my system? What amp would you use ?? maybe 15 amp.or slow blow 10 amp?

A I agree, nothing like steering with the wheel.....like we should be. A lot safer keeping your eyes on what'sin front of you. The cable system is the way to go as far as I am concerned. Installed it on my Hydra Sports 2 years ago and love it. No issues, no problem. I also have the Troll master Pro 2 running my kicker for trolling. Marty

Question Tim, are those Cisco's hand remote or hard switches. I just hate to put anymore holes in my boat with all the hardware and mounting of accessories...one of these days I'm going to sinlk it !! heehee

Thank you guys for the answers, comments and suggestions. Rod Hog, was the price for qty 1 or 2 units? I see two for $507 including free shipping It would be sweet if they did come out with a hand remote ! Of coarse, my luck, they will offer this after I buy mine

I want to convert my manual Big Jon mast to electric. Big Jon mentions the kit ($507 is the cheapest I can find) comes with 20' cord and switches. My question is are the switches simply a toggle that I need to mount or is it a wireless. It would be nice if they did make a wireless controller. I hate drilling more holes in the dash panel or boat. Any suggestions? Thank you in advance guys. Marty

Heay guys thank you very much for the suggestions I'll look them up

It's time for me to replace the drags on my 4 Penn 320's. I just cant's find a good vendor out there that can ship a simple product. I tried this Rod-N-Reel Depot & Cast Away Tackle and I had to cancel from both of them due to delivery issues or lack of responding in general. Sorry , but I just can't support or give them my business if they can't or want to sell there product. Looking to use Carbonex type drag washers or another that will last. Any good reputable suppliers that you can suggest?

Anyone have experience in having there hds8 interface with a s1000?

Hello, Does anyone have any experience in wiring these two devices and what color NMEA wires should be connected. I wired all 4 of my wires (per Raymarine Tech Guy) and I get a "no fix gps". Very confusing and many forums that I read do not agree with each other. Do I need to be switching something on my new HDS8 to let the HDS know there is another device connected? I was reading there is a configuration that has to read "on". Anyone know where this is located on a HDS8? Thank you in advance.

Thank you guys for your valued comments and suggestions. I will take this on the lake with me.

Hello, I never really targeted the Browns at Olcott before. I understand by the postings that they hang out in under 40' water . Do they hang low in the water.h spoons What lures and set up does everyone use ? J14 Rapala ?? spoons? . Are they to attracted to spin-doctors & flies? I was planning on flat lining rigging #40 jets with spoons back 100' or so. Thank you in advance