Jump to content

kayaker919

Professional
  • Posts

    164
  • Joined

  • Last visited

Everything posted by kayaker919

  1. price reduced, PM if interested. Webster pickup only, due to size does not fit in flat-rate package with necessary padding.
  2. Contico hardside plastic bow case - approx: 52" x 19" x 6" Softside padded bow case - approx: 52" x 19" $50 for both cases; Pickup in Webster; PM if interested.
  3. Very good condition, Metal Riser, 66" AMO, 50# at 28" $125. Pickup in Webster. PM if interested.
  4. Qty 2 - Yakima 66" Round Crossbars Qty 4 - Yakima gunnel mounts for round crossbar Qty 4 - Yakima locking clamp on Q-towers (for bare roofs) Qty 4 - Yakima Q99 clamp/clip adapters (currently installed on towers) Qty 2 - Yakima Q2 clamp/clip adapters (loose) Qty 2 - Yakima locking rail rider towers (for vehicles with existing slotted rails) Qty 4 - Yakima locks ..... and 2 keys! 8^) Instructions, tools, etc. as seen in photo. $250 $200, $150 or BO, Pick up in Webster, NY PM if interested.
  5. 20lb Shark downrigger weight. $75. $50 Pickup in Webster. PM if interested.
  6. Bimini Mount Rocket Launcher, width was modified, but it has never mounted and used - $50 $35 or BO ~63.5" center to center, could be shortened a couple inches in necessary. Pickup in Webster, PM if interested.
  7. Summit Viper XLS Climbing Treestand, light weight aluminum, easily packable; used less than a dozen times. Includes original safety harness, rapid climb stirrups, instructions (there are also videos online) and fanny pack shown in photo. $150, pickup in Webster. PM if interested.
  8. No experience, but some ideas.... The signals do share a common "return" through the water, so that might be coupling somehow. However, I would think the starboard probe would swamp any signal coupling. I assume you verified the starboard probe works with the port probe not in the water? If you swap probes does it follow the probe? If yes, maybe low battery in starboard probe?
  9. You do not need to electrically connect the coated cable to the rigger spool unless the rigger uses that for autostop, or positive ion control like some Cannons. It is not needed for the Depth Raider. I should have thought of this on my original response, but you can connect the ground wire directly to the lower lug on the probe to increase the signal strength for testing vs dropping in bucket. Your antenna should work then. You can also theoretically increase the signal strength in actual use by taping or otherwise insulating exposed metal that contacts the top lug of the probe, just make sure your swivel still works!. I tape up the clincher release with the stretchy, self-adhering tape down to the top of the swivel. Nothing on rest of swivel. I did coat the probe tab with "liquid tape" where the swivel does not contact, but don't know if it made any difference. I get 150ft with x-version Depth Raider.....175+ft with wet towel....YMMV
  10. Did you put the ground wire (negative power connection) in the bucket too? If a metal bucket just connect ground wire to bucket.
  11. See the diagram below and in the following link. Add-A-Battery Kit - 120A This system keeps both batteries charged automatically, but isolated so your start battery does not get discharged by your electronics. The switch is ON/OFF/BOTH. BOTH is only for emergency if your start battery is low for some reason.
  12. Try this...Under "Account Settings", select "Content View Behavior" then select "Take me to the latest comment" or "Take me to comments I haven't read"
  13. Photo attached Sent from my SM-G781U using Lake Ontario United mobile app
  14. Tough fishing out of ibay so far this spring, a few sporadic salmon and incidental lakers, have not tried for browns. Sent from my SM-T820 using Lake Ontario United mobile app
  15. You “can”, but to reduce the possibility of ground loops and interference between electronics, you should connect all negative returns to the ground bus bar. If you cannot upgrade the bus bar you would be better off “double lugging” the second battery to your ground bus bar than connecting it to the negative terminal of the first battery. See the diagram below and in the following link. Add-A-Battery Kit - 120A
  16. https://www.tacklehaven.com/depth-raider-probe-klincher-kit-part-dr-1016/ See photo in link. Sent from my SAMSUNG-SM-N920A using Lake Ontario United mobile app
×
×
  • Create New...