Jump to content


  • Posts

  • Joined

  • Last visited

Everything posted by phil2

  1. Allot of Michigan guys only run spin doctors and run 2.3 2.4 mag divers ticking bottom. Riggers bouncing. And long lines and high divers out for salmon
  2. Lasts for yrs. Clean it let it dry and spray it good. Especially on seams
  3. Scotch guard tent sealer and water repellent. Best I have used.
  4. Not a issue turned it into a race car turns on a dime and no weird vibrations. No more issue with autopilot maxing out with the big amish trolling bag. A definite need to do.
  5. I had a custom made set put on . Night and day with and without. I went 1 inch lower and 3 inch back. I will post a picture when I find it
  6. Have 2 lms 350 head units one is like brand new if someone can use . I can meet in Pulaski to Oswego. 40 bucks
  7. You could run a big board like a TX 44 or the big offshore off a butt section of a rod with 60 lb braid . but with a small boat run the in lines 12s for browns or up to 5 color cores and TX 44s or the big offshores up to a 500 copper. Stick a Sam's pro release on the big boards so the release, and be done with it. I run inlines all summer never have a issue.
  8. Price drop $550 with bases!
  9. I have 3 props forsale. All like new condition. First is a Mr minus 18x19 3 blade $400 Second is a worked 18x18 mr minus 4 blade. $400 and last is a new mw 18x18 dyna quad $800 Will work great on a 350 or 454 single screw boat. If anyone wants to see any I'll be in Mexico this weekend. Can put in truck
  10. Selling 2 mag 20 ts both with 3 rod holder stainless booms new 200 lb cable. Ball retrievers and covers. 600.00 for both. Pickup in Pulaski.
  11. Think they must of had bad cable . I put new spool on a mag 20. Lost a shark and a x4d probe . Then again bouncing for Lakers cable jumped the pulley went between the pulley and bolt cut it like a knife. Then another when ball came out of water I must of shocked it and it snapped between the ball and pulley. Switched to 250 lb Mason. Knock on wood haven't broke any off. Wait ripped a mag 10 off the boat when I got hung up. Expensive mistake.
  12. Have 2 mag 20 ts stainless 1 new board both with new 250lb wire duel holders and ez pull ball retrievers. $800 available in Saratoga or Mexico.
  13. Just hit the plugs not to much pull the kill switch and turn over a couple times. Shooting some in airbox while running won't hurt anything. Do lower unit oil change and keep trimmed all the way down.
  14. I had the 262 ran great 28 mph got beat over 3 ftrs . You have to take your time turning in rough seas they do ok seem a llitle top heavy. Get some slop. Stringers are know to be crap. Feel up under all the drain holes if your finger goes in to mush looking at a Stringer job. Or drill and fill . Great boats there getting up in age and need love.
  15. I have a 94 with twin inboard 7.4s thinking of adding a kicker it has a raymarine autopilot is there a way to connect kicker to it? I looked at my tiller the arm looks electric one wire controlling the ram on the rudders.
  16. Thanks guys prob end up replacing it lasted a long time one ride lol. Brand new in September. Obviously faulty.
  17. Just was looking at manuals says once under 10 volts or over 13 charger it wont charge . sounds dumb to me.
  18. Been working on the new boat. Seems like house battery is dead 9 volts or so. I have shore power with a adapter for a regular lead cord. Light for charger comes on cycles then goes green charged. Have 2 sets of wires one going to a isulater other to battery switch. Does the charger need full 30a to work? Or will regular lead be fine? Lost with it isulater should put power to that side once below 12 volts charges when running mains but not shore power.
  19. Took out a hds5 gen 2 just bracket and unit. No power cord or transducer. Im in Mexico until Tuesday. 300 obo
  • Create New...