Mikeyman104

For sure. Oswego county issued a local state of emergency for it. Schools and daycares now closed. If you want to see what the totality is like, go outside for about 4 minutes around midnight then go back inside.

Hope the fishing is good for folks who plan to be out during the eclipse. Think it'd be pretty interesting to be on the water during the event. Also, I'll be curious to hear any fishing reports that come out of it and if any unusual fish activity happens. I'd be neat if the fish start feeding like it's dusk/dawn when the totality is going on. Best of luck to anyone who can get out fishing during it!

Got the switch in and I feel like I've read that most folks seem to just leave it on 1+2. That about right? If that's the case, would the house try to start the motors? Or is it better to start motor with cranking battery and then put it to 1+2?

Had the day off yesterday so tried tackling some of the wiring addressed above. After getting a hand on stuff, it seemed like everything on my console, except my fish finder, was running off my cranking battery. What I thought was my house battery only had the fish finder and trolling motor on it. The on board charger also throws a lot more wires into the mix. Based on my findings and some of the suggestions, my plan was to separate my trolling motor completely, add a battery switch and add a real house battery. Thinking I had traced the wires correctly I started making some cuts only to find out they weren't the right ones. Feel like that's electric 101 and I wasn't off to a good start. After splicing my errors back together it was back to square one. Ended up putting my house battery under the main console and running wire to the back of the boat and tie it to a battery switch. From there I ran wire back to the console to a fuse box and have all my switches, lights, and pumps running off of this. Still got to tackle putting the cranking motor on the switch, adding my kicker and wiring up the riggers and depth raider. I'll probably put another fuse box or bus bar in the back to run this stuff off the switch. Thinking the depth raider and big Jon's have fuses or breakers on them so should be protected. My big Jon's also have the 110 plugs on them so will an outlet to connect those up. It's all a learning experience for sure but appreciate all the input and suggestions

Dang, I forgot about my depth raider. Got to figure out a spot and wiring for that too! Most the above is just what's going on in the back of my boat and I haven't even started addressing the front with the trolling motor and house battery either. Might just end up rewiring a whole bunch of it, adding a battery switch, adding a fuse box (if there isn't one already), and moving batteries around to get it to what I'm thinking it should be. Poor boat...

Understood and appreciate the feedback. Recently, I picked up a tiller 9.9 kicker with electric start and a 6amp alternator. Can I just wire this right to my starting battery along with down riggers? Seems like a lot of connections for the terminals on the battery (main motor, kicker, 2 big jons, i think my bilge and a noco charger). Guessing a bus bar or something would be better for the big jons this way i'll only have 4 or 5 connections on my battery post? Or maybe something like these terminal clamp connectors might be a better fit (Battery Terminal connectors)? Solid chance I'm over thinking, but i try not to mess around when it comes to electrical and want to make sure it's right.

Well after getting my motors running, this cold weather stretch got me worrying so figured I'd bring my kicker indoors and then trim my main all the way down. Turns out, all the way down is below grade, even with the trailer jack down too. Ended up putting the boat in the yard and digging a hole under it to get it down. How's everyone else get their motor all the way down? Didn't think I had a long shaft main motor but maybe. Never actually measured it

Well got it on tonight. Not the cleanest install but it's on there. Have 1 "in" port and 2 "outs" on the separator, with the other "in" blocked off. Tossed a couple check vales on the "outs" as well and clamped the heck out of everything. Put some gas in the separator and started up the main. Ran it for about 5 and did good. Next, fired up the kicker for the first and let her run for a bit too. All seems to be working. Couple of questions for you all though. Do you all trailer your kicker around with it tilted up or down? Think down is the way to go. Also, how you get more wires through the gasket things?

They look great!

Thanks all! Just got my kicker on the back of the boat and looking to put the F/W separator on sometime this week or weekend. Think there in the splash well will work based off of the input above so that'll be its home. Think I'll also put a couple check valves in the "out" gas lines to help prevent the motors stealing gas from each other too. Again, greatly appreciate the inputs and the responses, thanks all!

I was reading through some old posts, specifically the one below, and I liked the idea of adding a fuel water separator to my boat and then tie the kicker to the separator. My boat doesn't currently have a separator on it, so I'm wondering where the best location to install one is on my 196 starcraft superfisherman. I was thinking of putting it around here in the back where the fuel line comes out, but can it be exposed like this and are there other considerations I should be taking into account that I'm missing?

Thanks all! I hadn't thought of wiring the riggers to the cranking battery because I did that in my old boat and the riggers drained it. This was cause my kicker didn't have electric start or an alternator so while I was trolling and using the riggers, it was just draining my crank battery the whole 6 hours. I do need to buy a kicker for my new rig so i'll be looking to see if i can get a deal on one with an alternator. I'm not an electrical guy by any means, so i've never really wanted to dive into the battery switch and isolator world. Then again, in my old boat i only had 2 batteries and everything was just wired directly to where it needed to be. I got to read up more on both the switches and isolators to get a better understanding of them. thanks again all for the suggestions and input!

Thanks Hop, is the floor storage flat up there? how did you strap the battery down?

For the batteries you have in the bow storage, are they strapped down? Thinking they almost have to be Yeah, was thinking i'll have to do something like that. Thought the cranking battery should only be used specifically for the motor though?

This mild weather has got me thinking on how I can wire up my boat for trolling come spring time. I have a 2001 Starcraft 196 superfisherman that I'm looking to put some electric big jons on, but am not sure how I should go about with wiring and battery set up. Currently, there's 2 batteries in series under my consoles that run up to the bow to control the 24v trolling motor. Off of the battery under the driver side console, I have my Garmin fish finder wired directly to it. I was reading online that this will likely drain/kill my batteries quicker so thinking i'll have to address this too. Main motor is on a battery by itself so in total i have (3) 12v's currently on my boat. Ideally, I'd be looking at a single 24v lithium for my trolling motor and then break the other 12v electronics (big jons and garmin) out by themselves, but that's not in the budget. Was thinking of sticking another 12v up in the bow to run the garmin and big jons off of that, but no real good spot to put it up there and be running the wire a decent ways? Pic is the way it's kind of set up now and wondering if there's a better way i should be going about this. Input/suggestions appreciated. Thanks all!

Most recent update: took it to a shop and they replaced the water pump and thermostats. Pumps water good about 5-10 seconds after start up, but nice solid flow now. Much better compared to when I bought it. Best part was the guy told me it looked like someone replaced the impeller with a cheap one that is way more flexible than the OEM version. I told him, yeah I did that, and that's when it all went down hill . Think I'll pay for the OEM parts from now on just for that peace of mind. Thanks again to all for the comments and feedback.

Different things learned while trying to do this: 1. The speedometer tube is a pain to get back into it's little hole once you drop the lower unit 2. Make sure the shift shaft goes back into where it's suppose to. Launched the boat this morning and the lower unit was stuck in forward gear. That was quite a jolt at the dock and glad the ropes held. Shifter was in neutral so she started, but I dropped the lower unit while in forward and then missed it going back in, so gears were in forward, but shifter in neutral. 3. I shouldn't quit my day job to be a mechanic. Now I got a constant beep above 2500ish RPM and she still takes quite a while to start spitting water, so probably going to just take it to a dealer. Thinking it has something to do with the cooling system cause I've botched this project haha. I was always under the same impressions as some of previous comments in that as soon as it starts it should have water coming out. It still doesn't for me, so might be poppet or thermostat? Getting to the poppet looks like a pain, but might give the thermostats a quick look before I take it in. Thanks all for the inputs and help on this.

Got the new water pump kit in. Gaskets were in the correct order this time and had a friend help me with getting the lower unit back on. I was say, getting the speedometer tube back in its hole is an experience but way easier with 2 people. Got the muffs on and fire her up. No water coming out the pee hole for about a min but then it slowly starts to come out. Give her a bit of gas and good stream comes out. Let off the gas and the stream slows down as well, but keeps flowing. Seems to me that this is just normal for her I guess? Everyone/everything pees differently I suppose

I still consider myself very green when it comes to trolling, but I've has pretty good success near the bottom in 70-90 FOW pulling cowbells and spin n glos for lakers. This is always a bit of an adventure as the lake has some pretty significant depth changes that can sneak up on you, so make sure to adjust the riggers as needed and not get snagged. Down speed around 1.7-2.0 mph and if you don't have a probe, usually was around 2.3-ish on the gps speed.

When I took it out the boat out for a ride (ran a couple miles at about 4000 RPM), I didn't get any alarms or beeps, so hoping it was ok and not running hot. Once she got running, the flow improved. Maybe it's normal for these motors? Either way figured it'd be good to replace the impeller (till i messed it up ) Also had to google what a poppet valve is, where it's at, and what it does. Looks like a pain to get to.

Thought about this as well. Once that gasket got chewed up, I was worried about it getting lodged up in the thermostat or elsewhere in the system. I flushed it afterward it got chewed up, but thinking about replacing the thermostats just in case.

Thanks all! Cleaned out the pee hole with some weedeater string. That worked great so thank you for the recommendation. Unfortunately it still wasn't spitting but I at least knew that was clean. Took the lower unit back off and gasket was all torn up again. Watched some more YouTube and looks like I had the gasket order on wrong, so user error. Got another kit on order. Tried to flush everything out best I could. Also turns out this new motor has its own flush port, so ran some water in there for a bit too. Hopefully I'll put it together correctly next time 😆 (instructions are just someone else's opinion)

I recently picked up a new to me boat, a 2001 Starcraft 196 Superfisherman with a 2004 150 Mercury Optimax on it. When the guy was showing me the boat, he hooked up some muffs and I noticed how it took a while for it to start peeing but eventually it started to flow ok. Fast forward to my first outing with the boat and pretty much same thing was going on. Starts with a trickle but then gets going ok. I chalked it up to needing a new water pump, so I tossed a new one on tonight and then put the muffs on it. Nothing comes out. Makes me super nervous running it without any water coming out of the tell tale so I shut her off and pulled the lower unit back off. Guessing I did something wrong with the install cause one of the gaskets got chewed up so I tossed the old one back on. Hooked the muffs up again but she still wasn't spitting. Maybe a piece of gasket clogged everything up? I pulled the tell tale tube off and blew through it and it seemed fine. Anyway to clean out the system?