Legacy

Paypal also doesnt do refunds past 45 days.

You can get numerous seasons from a good quality wire. Its made from stainless steel so it will hold up to a lot. my reels are spooled up with 1000'. Really the only time I replace wire because I have 650' or less on the reel. (Which will happen eventually from cutting back and retying.) This little of line on the reel will make the counter inaccurate and of course leaves you less line for fish to take. Sent from my C771 using Lake Ontario United mobile app

Welcome to the site! Sent from my C771 using Lake Ontario United mobile app

Welcome to the site!

My big boards are in the water from flatlining Spring Browns in shallow water to summer copper fishing KIngs to plug fishing Kings in the fall off the pier heads. Big boards are the way to go when pulling multiple mono flatlines When one of those lines releases you can simply slide the others down in its place. Assuming all the lines are the same you will have minimal tangles. The idea of doing the same thing with multiple coppers or leadcores just isnt a good idea. You would have to reel in lines to reset a side and this is the dilemma with using big boards with this setup. If your plan is to run multiple coppers per side then Ideally small boards are the way to go. Church TX22 for short coppers and TX44 for long coppers are great choices for that.

Welcome to the site!

I fished braddocks yesterday and walked away with a skunk. 5 tip ups with 2 flags. Both ended in dropped baits. 5 tip downs, 1 deadstick, and 2 jigging rods = zero perch. I never even had hit and never saw a fish. It wasnt just me, word on the ice was it was just terrible fishing. Terribly slow from Braddocks to Iron Bay.

3 sets of Cannon rear mount dual rod holders never used, opened box, (can also be boom mounted or single rear mounted) $45 each

double or single surgeons loop for me!

Check out Purple Taco Fly supply... http://www.purpletacoflysupply.com/

For copper lengths 250'-500' = Okuma Clarion 553LS or Okuma Convector 55L. I will say, 500' will leave you with less then 100' of backer though. Solterra 50 is a better choice for 500' or more.

I would depend on the average depth you would like to target kings and this may vary depending on what port you fish from. In 2013 my answer would have been 400' copper but in 2012 my answer would have been 300'. If you are looking to get your first copper rig then I would suggest something between 400-500'. Reel size isnt overwelming with copper lengths of this size. Take the time to mark out every 50' of line and this will give you the opportunity to fish it at different lengths (150, 300, etc) as a chute rod. This one setup will help you learn the fundamentals of copper fishing and soon you will own 1/2 dozen setups!

Albright knot for your connection to backing and also to leader. Sent from my C771 using Lake Ontario United mobile app

This is what your looking for then... http://www.fishusa.com/Product/Precision-Trolling-Big-Water-2nd-Edition

My most productive 60# setup was 300' on an Okuma Clarion 553. The stiffness of the copper takes some getting use to but to the guys already using stiff copper will not see much of a difference. Some big advantages are it ability to achieve depth with less line out and it get to its depth faster and holds it truer. This article really puts it all out there. http://www.bloodruntackle.com/60lbcopper/

The Solterra 50L

You could run wire on most any new diver rod without any issue. The problem is the tip guide creates friction and heat which weakens wire. It can be witnessed by the excessive curling of the wire. Installing a really tip will eliminate the majority of this issue. Is it absolutely necessary? No but it is certainly better with then without Sent from my C771 using Lake Ontario United mobile app

YupSent from my C771 using Lake Ontario United mobile app