MCF

SOLD 8/27/12 I know there are a lot of these out there as boat haulers/hunting vehicles. Near perfect 15 inch rim for Astro or Safari with center covers. No staining, peeling, too good for winter use!!!!!! $100 for set or best offer In Dunkirk NY.

additional pictures added.

You can put any motor on there you want-the range should be 40-90 hp. The last motor on it was a Mercury.

SOLD 9/16/12 NO MOTOR. 1986 Sea Nymph CC-171 17 ft aluminum center console and 1981 EZ loader trailer. Boat needs general clean-up and could be used now. Needs seats and eventual interior upgrade but floors and transom solid. Hull has no dents. Console and windshield fine. Trailer has brand new tires this spring. I am on to next project, $875..00 or best offer . Located in Dunkirk, NY

going through the garage, still have these available 8/8/12

bump

to the top

to the top

I know it is a tri-hull but someone here may have a use for it or be interested in the package for the motor 75 Glastron 17 ft tri-hull(registered as 17, actually the 186 Swinger model) and mooring cover, 84 Johnson 70 hp with power trim and tilt(this is 3 cyl), 2200 lb calkins roller trailer. Boat can be used now, however it will eventually need transom repair. If you are using it on an inland lake, it should give you years of service before you need to do something. Or re-inforce it now with some aluminum plates. In any case, it is not going to fail without advance warning. Floor and rest of hull solid. Seats are recently installed, still have plastic shipping corners on them. Interior-other seats, side panels, bow seats are excellent. Motor runs good, just needs tinkering like sticking fast idle. Trailer has brand new tires, which were installed on 7/1. $1000.00 or best offer Boat located in Dunkirk, NY. Will provide motor pictures later.

A good quality grease not necessarily marine. Bearing failure, like the trailers you see on the side of the road usually come from lack of maintenance, no one took the time to either spin the wheels or pop the cover off. Or someone tightened things too tight.

I certainly would not want to sell something to someone that could not be registered, I am clarifying this question now. But for example an unladen trailer weighing more than 999 lbs, has an issue getting registered as a homemade. And a trailer that would fall under the title rules. The unladen weight on this is in the neighborhood of 350 lbs.

bump

This has worked in the past, try some of the good dry gas, dump enough to cover whatever gas you have in the tank, run it at idle long enough to get it circulated through the system, then go for a ride. Sounds like you have a bad tank of gas to me, I would try this before going to the next suggestion, water separator or fuel filter.

It would be helpful if posters put their location when looking for something. My suggestion would be to get on Craigslist in your area and look. For example in Western NY, there have been a few posted this spring/summer.

As I recall when the bellows went on my OMC Cobra that I owned years ago, the marina owner said the Mercruiser was the most involved to change.

price reduced another $50.00 to $300.00. Would like to move it this week.

price reduced-to the top.

you have a pm

bump

bump

This will have to be registered as a homemade, I have no paperwork! EZ loader roller boat trailer with relatively new tires, tires still have rubber nubs on them and rims. Dolly wheel, bearing buddies. All rollers good. Have one rear light working, may need replacement for the other, 8.99 each at harbor freight. Overall trailer is in good shape, sat inside for an extended period of time $300.00 or best offer. Can provide you with whatever other pictures you need to address your questions. Located in Dunkirk/Fredonia NY

bump

bump

bump

I think we all need some more details, symptoms. Is it stumbling at high speed, has a miss at high speed etc? Has it had a set of new plugs recently? How old is the motor? Do the plug wires etc look good, no cracks etc? Permanent gas tank and if so how old is the gas? Those are the questions that any mechanic is going to ask or anyone on here with a suggestion? thanks