sherman brown
Members-
Posts
1,050 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Everything posted by sherman brown
-
Looking for w.o.t for 1982 sportcraft 25ft
sherman brown replied to SALMONBOY35's topic in This Old Boat
do you have your gps set on mph or knots? I think a knot is something like 1.3 mph so 22 x 1.3 is a little over 28 mph. check your gps and see which one your using. -
Looking for w.o.t for 1982 sportcraft 25ft
sherman brown replied to SALMONBOY35's topic in This Old Boat
the speed and the rpm's don't seem to match. I don't run my 5.7 over 5000 rpm's in my 21' glass boat and run well over 30 mph. maybe your prop hub is slipping. are you plaining off ok? what type speedometer are you going by? if your going by a dash speedometer that is run off water pressure the pitot tube could be blocked. -
-
-
Sold / Closed 191 Starcraft Islander: SOLD 4/30/19
sherman brown replied to chowder's topic in Boats for Sale
-
-
-
if you are going to be running riggers its probably best to use some type of backing plate or maybe fender washers. I just have my tracks mounted with ss screws screwed into the fiber glass. works great for running 3 dipsy's on each side. however I did run 2 big jon 48" boom with 12# weights last yr on one trip. didnt have any problems at all. but it was a one time thing. if I decide to run them all the time i'll switch to machine screws and put fender washers and nuts on my tracks.
-
-
I like a longer track so I can space my holders out. I started with a 24" but didnt have enough spacing for 3 rods running dipsy's. so I added another 24". now I have room for 3 rods and one for the net. you cant go wrong with the longer track. I have the cannon single axis ratcheting holders and they are the best holder you can get in my opinion. I tried the double axis but the left to right adjustment was from one pin hole to another. the single axis is as much or as little as you want.
-
-
I have used seaguar inviz x for my downriggers on erie's central basin. but I split a spool on 2 reels. never used it on a spinning reel.
-
for sale : usa 1988 115 mercury 25" shaft
sherman brown replied to reelkrazy9's topic in Classifieds - Buy, Sell, Trade or Rent
-
-
Wanted wanted traxstech ratcheting rod holders
sherman brown replied to sherman brown's topic in Classifieds - Buy, Sell, Trade or Rent
still looking. -
Sold / Closed Sea nymph 22 ft great lakes special $3500
sherman brown replied to slow rollin's topic in Boats for Sale
-
Looking for a Trolling Plate
sherman brown replied to s072784's topic in Classifieds - Buy, Sell, Trade or Rent
-
Looking for a Trolling Plate
sherman brown replied to s072784's topic in Classifieds - Buy, Sell, Trade or Rent
-
yeah it sounds like you might be over correcting. I trolled for yrs with an I/0 before getting auto pilot. you do have to stay alert and not let the bow get to far over before making a small correction then wait to see if it was enough. try to always troll with the wind or at a angle with the wind. trolling against the wind is just asking for steering problems. I once fished by myself in pretty rough water. I angled the boat with the wind, tied a 6v flashlight to the bottom of the steering wheel. and it did most of the steering for me. I only had to adjust once in a while.
-
Wanted wanted traxstech ratcheting rod holders
sherman brown replied to sherman brown's topic in Classifieds - Buy, Sell, Trade or Rent
still looking. -
mounted with a good antenna. something like the Shakespeare 5225 xt. the quality of the antenna is more important than the radio. just get a radio with the bells and whistles you want. but do not scrimp on the antenna. a hand held is good around the dock or in a group of boats. but a fixed with a good antenna is good for 15+ miles. I splurged and got a new radio with built in gps for my boat.
-
I had my youngest son drain my 5.7 a few yrs ago. took the boat in to the marina for an oil change in the spring. all the freeze plugs on one side was out. very lucky the engine didnt crack. it turned out the drain was stopped up with sand and the motor hadn't drained. now I make sure the water drains and I leave the petcocks open until I use the boat in the spring. I wont venture to guess if the small amount of water in your motor would cause a crack. why didnt you leave the plugs out so any extra water could drain?
-
What size dipseys
sherman brown replied to hookedupf7's topic in Questions About Trout & Salmon Trolling?
I switched to the lite bite slide divers a few yrs ago and would never go back to std divers. I don't use the slide part but lace a piece of heavy braid through the back then attach my snubber then a 6' to 8' fluro leader. I tie to a split ring lace it through the back going in the lite bite arm. set the tension loose and the diver will trip on small fish. for walleye they are the best diver made. -
I would list them for 100.00 each. thats a fair price but not on the high end. you can always lower the price if they don't sell. but you cant raise the price once you list them and get flooded with buyers. i've seen them priced from 50.00 to 150.00. I sold the one I had for 60.00 shipped last summer.
-
12# balls are good for anyplace you fish erie. I used 10# on the western basin. but didnt like the blowback fishing 50' to 60' on the central basin so I switched to 13# pancake weights. 12# will work great either place. I run both harnesses and spoons in the summer depending on the fish. but mostly fish spoons on my riggers. for early trolling the westers basin (april early may) shallow diving cranks off riggers at 1.0 to 1.5 will catch fish. use bandits, reef runners, husky jerks, flatlined should catch fish. don't be afraid to try hot n tots as they was our staple back when I fished the western basin. there are so many eater eyes in erie right now you should be able to catch fish. we started fishing the western basin back in the early 80's. now is the only time i've seen fishing as good as it was then.